Quick Product Finder

APPLICATIONS

Use ¼% OWF. Fill dye tub with water and Antichlor. Circulate water for five minutes to give the product time to kill the chlorine. Add the fabric and continue as normal. If treating the water prior to adding the cloth is not possible, treating the fabric will not harm dyeing.

Antichlor should be used in the same way in a bleach bath where peroxide is used because chlorine kills peroxide.

SPECIFICATIONS

Appearance: Clear Liquid
pH: 10 ± 0.5
Specific Gravity: 1.20 ± .02

APPLICATIONS

ANTICURL NC should be applied on a regular pad. Solution concentrations of 2% to 5% are generally adequate, but higher or lower amounts may be required to effect the desired hand and properties.

ANTICURL NC requires only ordinary drying, no curing is necessary.

SPECIFICATIONS

Color: White
Form: Emulsion
Pounds per gallon: 9.6
pH (2% solution): 4.5 ± 0.5
Solubility: Completely soluble in water
Storage: Store in area above 40° F
Compatibility: Compatible with most finishing agents
Ionic Form: Nonionic

ADVANTAGES

- Eliminates foaming caused by dispersants, additives, or chemical auxiliaries.
- Will not spot.
- Forms stable dispersions.
- Highly effective - exceedingly small amounts needed.
- Has a sustained effect.
- No defoamer scum ring on equipment.
- Non-toxic.
- Completely biodegradable - will not pollute.

APPLICATION

ANTIFOAM NOS may be used at .25% - .50% levels or less. Application concentrations are determined by the degree of foam encountered. Best results are achieved when ANTIFOAM NOS is injected into the system prior to foam formation.

PHYSICAL PROPERTIES

Appearance: White, translucent liquid
Odor: Odorless
Solubility: Emulsifies in water
Ionic type: Nonionic
Density: 8.17 lbs/gallon
Package: 55 gallon drum
Specific gravity: .98

ADVANTAGES

- Eliminates foaming caused by dispersants, additives, or chemical cleaners.
- Will not spot.
- Forms stable dispersions.
- Highly effective - exceedingly small amounts needed.
- Has a sustained effect.
- No defoamer scum ring on equipment.
- Non-toxic.
- Completely biodegradable - will not pollute.

APPLICATION

ANTIFOAM WA may be used at .10 - .50% levels or less. Application concentrations are determined by the degree of foam encountered. Best results are achieved when ANTIFOAM WA is injected into the system prior to foam formation.

PHYSICAL PROPERTIES

Appearance: Translucent liquid.
Odor: Odorless
Solubility: Emulsifies in water
Ionic type: Cationic
Density: .993
Package: Plastic drum

APPLICATIONS

AQUA EDGE 100 should be applied full strength as an edge gum. The product is generally applied in a frame or in a tubular gummer. It can be applied with kiss rollers, pads, squeeze rollers, or it can be sprayed. Clean up with water. If dried, use REZ AWAY * full strength.

BENEFITS OF AQUA EDGE 100:
- Quick drying.
- Firm edge.
- Adheres to natural and man-made fibers; even fiberglass.
- Cleans up with water; or REZ AWAY when dried.
- Contains no V.O.C.’s.
- Non-polluting.
- Low cost.
- Higher line speeds.

SPECIFICATIONS

Color: White, semi viscous liquid
Form: Nonionic Emulsion
Pounds per gallon: 8.362
pH (2% solution): 8 ± 0.5
Solubility: Readily dispersed in water
Stability: Stable on storage, keep from freezing
Compatibility: Compatible with usual finishing agents

APPLICATIONS

AQUA EDGE 120 should be applied full strength as an edge gum. The product is generally applied in a frame or in a tubular gummer. It can be applied with kiss rollers, pads, squeeze rollers, or it can be sprayed. Clean up with water. If dried, use REZ AWAY * full strength.

BENEFITS OF AQUA EDGE 120:
- Quick drying.
- Firm edge.
- Adheres to natural and man-made fibers; even fiberglass.
- Cleans up with water; or REZ AWAY when dried.
- Low V.O.C.’s.
- Non-polluting.
- Low cost.
- Higher line speeds.

SPECIFICATIONS

Color: White, Semi viscous liquid
Form: Nonionic Emulsion
Pounds per gallon: 8.362
pH (2% solution): 8 +/− .5
Solubility: Readily dispersed in water
Stability: Stable on storage, keep from freezing
Compatibility: Compatible with usual finishing agents

APPLICATIONS

AQUA EDGE 68 be applied full strength as an edge gum. The product is generally applied in a frame or in a tubular gummer. It can be applied with kiss rollers, pads, squeeze rollers, or it can be sprayed. Clean up with water. If dried, use REZ AWAY*, a powerful cleaning agent, full strength.

BENEFITS OF AQUA EDGE 68:
- Higher line speeds.
- Low cost.
- Quick drying.
- Firm edge.
- Adheres to natural and man-made fibers.
- Cleans up with water; or REZ AWAY when dried.
- Contains no V.O.C.’s.
- Non-polluting

SPECIFICATIONS

Appearance: White, semi viscous liquid
Form: Nonionic Emulsion
Pounds per gallon: 8.362
pH (2% solution): 8 +/− .5
Solubility: Readily dispersed in water
Stability: Stable on storage, keep from freezing
Compatibility: Compatible with usual finishing agents

APPLICATIONS

AQUA EDGE 80 should be applied full strength as an edge gum. The product is generally applied in a frame or in a tubular gummer. It can be applied with kiss rollers, pads, squeeze rollers, or it can be sprayed. Clean up withwater. If dried, use REZ AWAY*, a powerful cleaning agent, full strength.

BENEFITS OF AQUA EDGE 80:
- Higher line speeds.
- Low cost.
- Quick drying.
- Firm edge.
- Adheres to natural and man-made fibers.
- Cleans up with water; or REZ AWAY when dried.
- Contains no V.O.C.’s.
- Non-polluting

SPECIFICATIONS

Appearance: White, semi viscous liquid
Form: Nonionic Emulsion
Pounds per gallon: 8.362
pH (2% solution): 8 ± 0.5
Solubility: Readily dispersed in water
Stability: Stable on storage, keep from freezing
Compatibility: Compatible with usual finishing agents

APPLICATIONS

AQUA EDGE 80 should be applied full strength as an edge gum. The product is generally applied in a frame or in a tubular gummer. It can be applied with kiss rollers, pads, squeeze rollers, or it can be sprayed. Clean up with water. If dried, use REZ AWAY*, a powerful cleaning agent, full strength.

BENEFITS OF AQUA EDGE 80P:
- Higher line speeds.
- Low cost.
- Quick drying.
- Firm edge.
- Adheres to natural and man-made fibers.
- Cleans up with water or REZ AWAY when dried.
- Contains no V.O.C.’s.
- Non-polluting

SPECIFICATIONS

Appearance: Pink, semi viscous liquid
Form: Nonionic Emulsion
Pounds per gallon: 8.362
pH (2% solution): 8 +/− .5
Solubility: Readily dispersed in water
Stability: Stable on storage, keep from freezing
Compatibility: Compatible with usual finishing agents

APPLICATIONS

AQUA EDGE 90D should be applied full strength as an edge gum. The product is generally applied in a frame or in a tubular gummer. It can be applied with kiss rollers, pads, squeeze rollers, or it can be sprayed. Clean up with water. If dried, use REZ AWAY*, a powerful cleaning agent, full strength.

BENEFITS OF AQUA EDGE 90D:
- Higher line speeds.
- Low cost.
- Quick drying.
- Firm edge.
- Adheres to natural and man-made fibers.
- Cleans up with water; or REZ AWAY when dried.
- Contains no V.O.C.’s.
- Non-polluting

SPECIFICATIONS

Appearance: White, semi viscous liquid
Form: Nonionic Emulsion
Pounds per gallon: 8.362
pH (2% solution): 8 ± 0.5
Solubility: Readily dispersed in water
Stability: Stable on storage, keep from freezing
Compatibility: Compatible with usual finishing agents

APPLICATION

Initially charge boiler with .5% to 2.0% Boiler Guard based on the amount of water held in boiler and holding tank. Add Boiler Guard weekly to maintain level.

SPECIFICATIONS

Appearance: Brown Liquid
pH: 11
Solubility in Water: Complete
Specific Gravity: 1.07
USAGE RATE: 0.5% - 2.0%

The amount of CAL AWAY required will differ depending of hardness of water. For complete removal of hardness use 100 grams of CAL AWAY for every 11 grams of hardness as calcium carbonate.

CHARACTERISTICS

Appearance: Clear Liquid
Specific Gravity: 1.4
Pounds per Gallon: 11.68
pH : 7.0
Volatile Organic Compounds None

APPLICATION

DBF-29 can be used in concentration of 3.0% to 6.0% (O.W.F.) depending on the speed time and temperature of
the bleaching cycle.

For best results add DBF-29 to the water and normal amount of hydrogen peroxide (usually 8-12% of 50%).

Proceed to run bleaching cycle as you normally run until desired white is achieved (usually 30-45 minutes once
temperature is attained.)

SPECIFICATIONS

Appearance: White powder
pH (2% solution): 11.0 + 1.0
Solubility: Completely soluble in water.
Weight/Drum: 500 lb.

APPLICATION

DBF-29B can be used in concentration of 3.0% to 6.0% (O.W.F.) depending on the speed time and temperature of the bleaching cycle.

For best results add DBF-29B to the water and normal amount of hydrogen peroxide (usually 8-12% of 50%).

Proceed to run bleaching cycle as you normally run until desired white is achieved (usually 30-45 minutes once temperature is attained.)

SPECIFICATIONS

Appearance: Light blue powder
pH (2% solution): 11.0 + 1.0
Solubility: Completely soluble in water.
Weight/Drum: 500 lb.

APPLICATION

DBF-30 can be used in concentration of 3.0% to 6.0% (O.W.F.) depending on the speed time and temperature of the bleaching cycle.

For best results add DBF-30 to the water and normal amount of hydrogen peroxide (usually 8-12% of 50%). Proceed to run bleaching cycle as you normally run until desired white is achieved (usually 30-45 minutes once temperature is attained.) Bleaching temperatures are 200 – 212°F in atmospheric equipment and 220 – 240°F in pressure equipment.

SPECIFICATIONS

Appearance: White powder
pH (2% solution): 11.0 + 1.0
Solubility: Completely soluble in water.
Weight/Drum: 500 lb.

APPLICATION

DEFOAMER 019-B is most effective in controlling foam in aqueous systems. Concentrations of 0.25% to 0.5% based on the total mixture are suggested as a start, but often lower amounts are found to give the required defoaming action. Should it be necessary, depending upon the process, small amounts of DEFOAMER 019-B may be added at various time intervals throughout the processing period rather than add the full amount at the start of the process.

PHYSICAL PROPERTIES

Color: White
Physical Form: Viscous emulsion
Odor: Mild to odorless
Pounds/Gallon: 8.17
Type: Nonionic, low silicone
pH (2% solution): 8.0 ± 0.5
Dispersibility in water: Disperses readily
Stability: Stable (under normal storage)
Stability on Heating: Stable up to the boil
Stability on Freezing: Permanent separation may occur

APPLICATION

DEFOAMER DC should be delivered into the system neat; not premixed with water because of separation of the active ingredients may occur. Injection into a feed pipe and mixing in the feed is acceptable because the entire package is being delivered at the same time.

Use concentrations can range from 20 PPM to .25% depending on the application and severity of foam.
Prevention of foam formation is always preferable to “killing” of foam.

PHYSICAL PROPERTIES

Color: White semiviscous liquid.
Odor: Almost odorless
Specific Gravity: .919
Pounds/Gallon: 7.64
Ionic Characteristics: Nonionic
Solubility: Completely dispersable in water.
Stability: Do not store in extreme temperatures.

APPLICATION

DEFOAMER ML should be delivered into the system neat; not premixed with water because of separation of the active ingredients may occur. Injection into a feed pipe and mixing in the feed is acceptable because the entire package is being delivered at the same time.

Use concentrations can range from 20 PPM to .25% depending on the application and severity of foam. Prevention of foam formation is always preferable to “killing” of foam.

PHYSICAL PROPERTIES

Color: Semi-transparent light yellow liquid
Odor: Mild oil
Specific Gravity: .919
Pounds/Gallon: 7.64
Ionic Characteristics: Nonionic
Solubility: Partially soluble in water. Completely soluble in oil and non-polar solvents.
Stability: Freezing point is well below freezing. If separation occurs, product can be reconstituted by mixing.

APPLICATION

DEFOAMER ML-2 should be delivered into the system neat. If premixed with water, do so at time of injection because separation of the active ingredients may occur. Injection into a feed pipe and mixing in the feed is acceptable because the entire package is being delivered at the same time.

Use concentrations can range from 20 PPM to .25% depending on the application and severity of foam. Prevention of foam formation is always preferable to “killing” of foam.

PHYSICAL PROPERTIES

Color: Semi-transparent light yellow liquid.
Odor: Mild oil
Specific Gravity: .919
Pounds/Gallon: 7.64
Ionic Characteristics: Nonionic
Solubility: Soluble in water.
Stability: Freezing point is well below freezing. If separation occurs, product can be reconstituted by mixing.

APPLICATION

DEFOAMER ML-X should be delivered into the system neat. If premixed with water, do so at time of injection because separation of the active ingredients may occur. Injection into a feed pipe and mixing in the feed is acceptable because the entire package is being delivered at the same time.

Use concentrations can range from 20 PPM to .25% depending on the application and severity of foam.

Prevention of foam formation is always preferable to “killing” of foam.

PHYSICAL PROPERTIES

Color: Semi-transparent light yellow liquid.
Odor: Mild oil
Specific Gravity: .919
Pounds/Gallon: 7.64
Ionic Characteristics: Nonionic
Solubility: Soluble in water.
Stability: Freezing point is well below freezing. If separation occurs, product can be reconstituted by mixing.

APPLICATION

DEFOAMER NSP should be added to the head box, the pulping tank or to some point prior to sheet formation. Add it to a location where there is a good deal of agitation to ensure that it is completely dispersed throughout the pulp suspension. Since each mill has different foaming problems, it is best to start with the amount of defoamer currently being used.

PHYSICAL PROPERTIES

Appearance: White semiviscous liquid
Odor: Mild to odorless
Ionic Characteristics: Nonionic
pH: 8.0
Dispersibility in water: Readily Disperses

APPLICATIONS

PAPER: Defoamer NSP-3 should be added to the head box, the pulping tank or to some point prior to sheet formation. Add it to a location where there is a good deal of agitation to ensure that it is completely dispersed throughout the pulp suspension. Since each mill has different foaming problems, it is best to start with the amount of defoamer currently being used.

COATINGS & INK: add to the initial grind to prevent air entrapment. Adding additional product during letdown will help ensure a foam-free product. Usage recommendation: .5 – 1.5% depending on need.

TEXTILES: Defoamer NSP-3 is designed for use in both atmospheric and pressure equipment. It can be dispersed manually or with automated equipment. Usage varies depending on application. The starting point should be .25% OWF. Decrease or increase the amount as needed.

PHYSICAL PROPERTIES

Appearance: White semiviscous liquid
Odor: Mild to odorless
Ionic Characteristics: Nonionic
pH: 8.0
Dispersibility in water: Readily Disperses

APPLICATIONS

DEFOAMER NZ-49 is most effective in aqueous systems. Depending on the application, concentrations of .01% to .50% may be needed to achieve a suitable defoaming action. In many cases, results can be obtained by using even lower dilutions. It has been determined that to defoam typical waste water with foam caused by nonionic and anionic surfactants that a rule of thumb is to use 1/5 the amount of defoamer to surfactant to prevent foam in waste water. For instance, if you identify that you have 100 ppm soaps for detergents, start with 20 ppm of Defoamer NZ-49. DEFOAMER NZ-49 is approximately 20% more active than our DEFOAMER WTC-10.

PHYSICAL PROPERTIES

Color: White
Physical Form: Semi-viscous emulsion
Viscosity: 1700 – 2500 cps
Pounds per gallon: 8.3
pH: 7-8
Type: Nonionic, modified silicone based
Solubility: Readily dispersible in water
Stability: Very stable product. If frozen, separation may occur.

ADVANTAGES

- Eliminates foaming caused by dispersants, additives, or chemical cleaners.
- Will not spot.
- Forms stable dispersions.
- Highly effective - exceedingly small amounts needed.
- Has a sustained effect.
- No defoamer scum ring on equipment.
- Non-toxic.
- Completely biodegradable - will not pollute.

APPLICATION

DEFOAMER WA may be used at .10 - .50% levels or less. Application concentrations are determined by the degree of foam encountered. Best results are achieved when DEFOAMER WA is injected into the system prior to foam formation.

PHYSICAL PROPERTIES

Appearance: Translucent liquid.
Odor: Odorless
Solubility: Emulsifies in water
Ionic type: Cationic
Density: .993
Package: Plastic drum
Shelf Life: 12 months

APPLICATIONS

DEFOAMER WTC-10 is most effective in aqueous systems. Depending on the application, concentrations of .015% to .50% may be needed to achieve a suitable defoaming action. In many cases, results can be obtained by using even lower dilutions. It has been determined that to defoam typical waste water with foam caused by nonionic and anionic surfactants that a rule of thumb is to use 1/5 the amount of defoamer to surfactant to prevent foam in waste water. For instance, if you identify that you have 100 ppm soaps for detergents, start with 20 ppm of Defoamer WTC-10.

For best results, DEFOAMER WTC-10 should be added at a point in the system prior to the foam formation. It should be thoroughly mixed to ensure the most economical performance. A good place to introduce WTC-10 is just ahead of the waste water discharge pump, this promotes dispersion of the product.

PHYSICAL PROPERTIES

Color: White
Physical Form: Semi-viscous emulsion
Viscosity: 2500 – 4000 cps
Pounds per gallon: 8.38
Type: Nonionic, modified silicone based
Solubility: Readily dispersible in water
Stability: Very stable product. If frozen, separation may occur.

APPLICATION

DEFOAMER WTC-15 is most effective in aqueous systems. Depending on the application, concentrations of 0.005% to 0.25% may be needed to achieve a suitable defoaming action. In many cases, results can be obtained by using even lower dilutions.

For best results, DEFOAMER WTC-15 should be added at a point in the system prior to the foam formation. It should be thoroughly mixed to ensure the most economical performance.

PHYSICAL PROPERTIES

Color: White
Physical Form: Semi-viscous emulsion
Odor: Mild, pleasant
Pounds/Gallon: 8.38
Type: Nonionic, modified silicone based
Solubility: Readily soluble in water
Stability: Very stable product. If frozen, separation may occur, but can be reconstitued upon thawing.

APPLICATION

DEFOAMER WTC-20 is most effective in aqueous systems. Depending on the application, concentrations of 0.0025% to 0.12% may be needed to achieve a suitable defoaming action. In many cases, results can be obtained by using even lower dilutions.

For best results, DEFOAMER WTC-20 should be added at a point in the system prior to the foam formation. It should be thoroughly mixed to ensure the most economical performance.

PHYSICAL PROPERTIES

Color: White
Physical Form: Semi-viscous emulsion
Odor: Mild, pleasant
Pounds/Gallon: 8.5
Type: Nonionic, modified silicone based
Solubility: Readily soluble in water
Stability: Very stable product. If frozen, separation may occur.

APPLICATIONS

DEFOAMER WTC-30 is most effective in aqueous systems. Depending on the application, concentrations of .005% to .25% may be needed to achieve a suitable defoaming action. In many cases, results can be obtained by using even lower dilutions.

For best results, DEFOAMER WTC-30 should be added at a point in the system prior to the foam formation. If should be thoroughly mixed to ensure the most economical performance.

If used to defoam a static foam problem, agitation or sprays may be necessary.

PHYSICAL PROPERTIES

Color: White
Physical Form: Semi-viscous emulsion.
Odor: Mild, pleasant.
Pounds per gallon: 8.38
Type: Nonionic, modified silicone based.
Solubility: Readily soluble in water.
Stability: Very stable product. If frozen, separation may occur.

APPLICATION

TEXTILES
1 - 2 % on weight of goods at 140oF - 160oF to remove oils, pectins, and other contaminants to permit processing of goods.

HARD SURFACES
Use 1-5 % to clean most oils and greases from surface. Recommended temperatures are 140oF - 180oF. Higher amounts of DYNASOLV 22F and higher temperatures may be required on some heavy greases.

SPECIFICATIONS

Appearance: Light yellow viscous liquid
pH: 7.0 - 8.0
Solubility: Completely soluble in water

APPLICATION

TEXTILES
1 - 2% on weight of goods at 140° F - 160° F to remove oils, pectins, and other contaminants to permit processing of goods.

HARD SURFACES
Use .1 - .5% to clean most oils and greases from surface. Recommended temperatures are 140° F - 180° F. Higher amounts of DYNASOLV 40 and higher temperatures may be required on some heavy greases.

SPECIFICATIONS

Appearance: Light yellow viscous liquid
pH: 7.0 - 8.0
Solubility: Completely soluble in water

APPLICATION

Due to the ability of DYNAWHITE to readily exhaust onto cotton and wool, it is best used in paddle machines, becks, and jets. It is formulated to ensure even application. Use rates are .75% to 1.25% depending on equipment. If added to the final rinse, run for 20 minutes at 120° F.

SPECIFICATIONS

Appearance: Clear yellow solution
pH: 10.5 ± .5
Specific gravity: 1.06

FINISH CM is substantive. When used to prevent penetration, begin with 3% to 7% by weight of the bath. The amount needed will depend on the type and density of the fabric. Higher concentrations of FINISH CM can be made if lower weight pickup is desired.

FINISH CM can be combined with softeners, lubricants, or anti-curl agents to provide the hand and properties desired.

APPLICATION

Apply by either pad or spray so that application is even and total wet pickup is 75%-100% of weight of fabric.

Dry the fabric before dipping in coating. You may find that the temperatures required to dry the fabric thoroughly may need to be increased due to the nature of the product. FINISH CM will not scorch, chalk nor dust.

SPECIFICATIONS

Appearance: Clear liquid
pH (as is): 8.0 ± 1.0
Solubility: Completely soluble in water
Specific Gravity: Minimum 1.360
Toxicity: None
Compatibility: Compatible with lower alcohols, glycols, glycerin, softeners, and salts in normal use concentrations. Also, compatible with most anionic, nonionic, and mildly cationic substances.

GFI-72 must be applied in a pad for the best economy. The amounts required differ from customer to customer. Solutions of 1% to 3% sufficient.

RECOMMENDATIONS

Start with a 3% solution padded onto the substrate and dry as usual. If this is successful subsequent solutions can be made to lower solutions. If the 3% solution does not work, increase to 5% and repeat.

PHYSICAL CHARACTERISTICS

Appearance: Clear, pale yellow liquid
Solubility: Completely soluble in water
pH: 4.0 – 5.0
Specific Gravity: 1.24

APPLICATION

HERRITON RH is applied in concentrations of 1-4% based on the weight of the yarn of fabric. It is generally added first, along with acetic acid to pH 5, run 10 minutes at 120° F, and then the dyestuff is added.

HERRITON RH provides maximum color yield and excellent levelness. It promotes even application of the various dye combinations.
HERRITON RH is biodegradable, contains no phosphates, and will not contribute to stream or water pollution.

SPECIFICATIONS

Appearance: Clear gold liquid
Type: Anionic
pH: 6.5 ± 0.5
Solubility: Readily soluble in water
Stability: Stable on storage
Compatibility: Compatible with most dyeing assistants and surfactants and stable in dilute solutions of acids, salts, and alkalies.

PHYSICAL CHARACTERISTICS

Appearance: White liquid
Solubility: Completely soluble in water
Boiling Point: 212°F
Melting Point: 32°F
Specific Gravity: 1.07
pH: 4.0 ± 0.5
Odor: Glue-like
Ionic Charge: Anionic
Tg: 28

RECOMMENDATIONS

HR-202 can be applied by dipping, spraying, or padding. Most applications require 1-5% O.W.B. Start with a 3% solution and determine if the hand is stiff enough.

For hat bodies or back coating, use 30% – 60% in water and apply as normal.

PHYSICAL CHARACTERISTICS

Appearance: White liquid
Solubility: Completely dispersible
Boiling Point: 212°F
Melting Point: 32°F
Specific Gravity: 1.07
pH: 7.5 – 8.5
Odor: Ammonia
Ionic Charge: Anionic
Tg: 14

RECOMMENDATIONS

HRX-610 can be applied by dipping, spraying, or padding. Most applications require 1-5% O.W.B. Start with a 3% solution and determine if the hand is stiff enough.

For hat bodies or backcoating, use 20% – 40% in water and apply as normal.

DIRECTIONS

MIRAFLOC works best at a pH between 8-10. Raise the pH to between 9 and 10 using either Pharagent S or caustic soda. With some agitation, add MIRAFLOC. The amount required will depend on the amount of suspended solids. Usually, .025% to .1% is sufficient. Once MIRAFLOC is added, recheck the pH to ensure that it is still 8-10. At this point, the floc will either sink or float depending on the specific gravity of the suspended solids.

Of the floc sinks, decant off the clear water and either return to your process for reuse or send down the drain. If the floc floats, either take the clear water from the bottom or skim off the floc.

The floc will have to be discarded in accordance with federal, state, and local regulations, depending on the characteristics of the waste being generated.

SPECIFICATIONS

Appearance: Clear liquid
Specific Gravity: 1.23
Weight/gallon: 10.26 lbs./gallon
pH: 2.0 to 3.0
Solids: 37% ± 1%

DIRECTIONS

MIRAFLOC 100 works best at a pH between 8-10. Raise the pH to between 9 and 10 using either Pharagent S or caustic soda. With some agitation, add MIRAFLOC 100. The amount required will depend on the amount of suspended solids. Usually, .025% to .1% is sufficient. Once MIRAFLOC 100 is added, recheck the pH to ensure that it is still 8-10. At this point, the floc will either sink or float depending on the specific gravity of the suspended solids.

If the floc sinks, decant off the clear water and either return to your process for reuse or send down the drain. If the floc floats, either take the clear water from the bottom or skim off the floc.

The floc will have to be discarded in accordance with federal, state, and local regulations, depending on the characteristics of the waste being generated.

SPECIFICATIONS

Appearance: Clear liquid
Specific Gravity: 1.23
Weight/gallon: 10.26 lbs./gallon
pH: 2.0 to 3.0
Solids: 37% ± 1%

USES

ODOR AWAY is designed to be used as low as 10 parts per million in some applications. However, higher quantities may be required, depending on the odor that is being masked.

SPECIFICATIONS

Appearance: Pale green liquid
pH: 3 ± 1
Specific Gravity: .987
Odor: Strong fresh scent

USES

ODOR-AWAY LF is designed to be used as low as 10 parts per million in some applications. However, higher quantities may be required, depending on the odor that is being masked.

SPECIFICATIONS

Appearance: Pale green liquid
pH: 3 ± 1
Specific Gravity: .991
Odor: Strong fresh scent
Shelf Life: Minimum 12 months

APPLICATION

OXYPAR can be used in concentrations of 2.0% to 5.0% (O.W.F.) depending on the speed of bleaching and whiteness desired. Using OXYPAR in conjunction with hydrogen peroxide will enhance the bleaching of cloth without any additional caustics or stabilizers needed.

OXYPAR is also used by individual laundries to return whites to their original brightness.

SPECIFICATIONS

Appearance: White powder
pH (2% solution): 10.5 ± .5
Solubility: Completely soluble in warm water

PHYSICAL PROPERTIES

Appearance: White semi-viscous liquid
Viscosity: 1000 cps
Tear Time: 10 – 20 seconds*
pH: 4.0 – 6.0
Solids: 42 – 43%

*Tear times are influenced by humidity and temperature.

Clean up is done with water or a mild cleaner like Grease Gobbler^TM.

PHYSICAL PROPERTIES

Appearance: White viscous liquid
Viscosity: 2000 cps
Tear Time: 7 – 15 seconds*
pH: 4.0 – 6.0
Solids: 54 – 56%

*Tear times are influenced by humidity and temperature.

Clean up is usually done with water or a mild cleaner. Once dried use Rez Away^TM to remove from surfaces.

PHYSICAL PROPERTIES

Appearance: White semi-viscous liquid
Solids: 54 – 56%
Water Solubility: Completely dispersable
Specific Gravity: 1.11
pH: 4.0 – 6.0
Tear Time: 7 – 12 seconds*

*Tear times are influenced by humidity and temperature.

Clean up with water. If dried, use Rez AwayTM to remove residue.

Rez Away is a trademark of Paradigm Labs, Inc.

PHYSICAL PROPERTIES

Appearance: White semi-viscous liquid
Solids: 54 – 56%
Water Solubility: Completely dispersible
Specific Gravity: 1.11
pH: 4.0 – 6.0
Tear Time: 7 – 12 seconds*

*Tear times are influenced by humidity and temperature.

PHYSICAL PROPERTIES

Appearance: Off white to light yellow viscous liquid
Viscosity: 2000 – 3000 cps
pH: 7.0 – 9.0

Clean up is easy with water only.

PHYSICAL PROPERTIES

Appearance: Tan to light brown viscous liquid
Viscosity: 2000 – 3000 cps
pH: 7.0 – 9.0

Clean up is easy with water only.

PHYSICAL PROPERTIES

Appearance: Tan to light brown viscous liquid
Viscosity: 2000 – 3000 cps
pH: 7.0 – 9.0

PHYSICAL PROPERTIES

Appearance: White viscous liquid
Viscosity: 2500 – 3000 cps
pH: 7.0 – 9.0
Solids: 49 – 51%

Clean up is done with water or a mild cleaner like Grease GobblerTM.

PHYSICAL PROPERTIES

Appearance: Semiviscious off white to tan liquid
Specific Gravity: 1.343
pH: 6 ± 1
Viscosity @ 25°C: 900 to 1200 cps

RECOMMENDATIONS

PARABOND LG-211 should be used as is. It can be used with kiss rollers, pumps, or sprays. Some thinning may be required if the product has sat for a while or if used in fine spray applications.

SPECIFICATIONS

Appearance: Clear, yellow liquid
pH (2% solution): 8.0 ± 0.5
Specific Gravity: 1.005 ± 0.005

PHYSICAL PROPERTIES

Appearance: White liquid
Solubility: Completely miscible in water
Boiling Point: 212°F
Freezing Point: 32°F
Specific Gravity: 1.06
Ionic Characteristic: Anionic
Tg: 36

RECOMMENDATIONS

Actual usage depends on results required. A good starting point is a 5% solution of Paracryl 125 padded onto the substrate. For substrates such as paper, straw, or wool hats a good starting point is 20% solution. Extract excess product to prevent migration and pooling during the drying process. Modify concentration.

SPECIFICATIONS

Appearance: White liquid
pH: 4.5 ± .5
Solubility: Soluble in water
Odor: Mild, sweet odor
Specific Gravity: 1.07
Ionic Characteristic: Nonionic
TG : -30
Solids: 50%

APPLICATION

PARACRYL 387 is recommended for use by itself or with other finishing products. Due to the fact that it is nonionic it is compatible in most finishing processes. Recommended usage is 2-10% depending on the type of fabric and amount of stabilizing required.

PHYSICAL PROPERTIES

Appearance: White liquid
Solubility: Completely miscible in water
Boiling Point: 212°F
Freezing Point: 32°F
Specific Gravity: 1.06
Ionic Characteristic: Anionic
Tg: 27
Viscosity at 780F: 10 cps

RECOMMENDATIONS

Actual usage depends on results required. A good starting point is a 5% solution of MI-7 padded or sprayed onto the substrate. For substrates such as paper, straw, or wool hats a good starting point is 20% solution. Extract excess product to prevent migration and pooling during the drying process. Modify concentration as required.

For use in inks and coatings use 20 – 50 % of Paracryl MI-7 depending on the water resistance required.

PHYSICAL PROPERTIES

Appearance: White liquid
Odor: Slight acrylic
pH: 2 – 3
Boiling Point: 212°F
Freezing Point: 32°F
Solubility in Water: Completely miscible
Specific Gravity: 1.067
Volatiles as Water: 55%
Viscosity: < 200 cps
Ionic Charge: Anionic

APPLICATION

PARACRYL NY-7 can be applied by dipping, foaming or spraying. Usage levels depend on the substrate and the stiffness required. Recommended use is 5 – 15% O.W.B.

PHYSICAL PROPERTIES

Appearance: White liquid
Solubility: Completely miscible in water
Boiling Point: 212°F
Freezing Point: 32°F
Specific Gravity: 1.06
Ionic Characteristic: Anionic
Tg: 36

RECOMMENDATIONS

Actual usage depends on results required. The product can be applied by spraying, dipping, or through a padding machine. Actual usage depends on the application.

APPLICATION

PARASCOUR 298 is used in concentrations of 1-3% based on the weight of the fabric.
A typical scour/dye procedure for cotton wool, or synthetic fabrics is as follows:
- Fill equipment, add PARASCOUR 298, and run at 100-140oF, depending on dyestuff being used.
- Add chemicals such as CARRIER MH, SORBASSIST N (wetter), DEFOAMER 019B, JT-4200 (lubricant), or HERRITON RH (leveler).
- Add dyestuff and follow regular dye procedure depending on type of dyes being used.

PARASCOUR 298 is an excellent detergent. It emulsifies oils and sizing agents and prevents their re-deposition. It is operative at temperatures as low as 80-100oF, but it performs best between 140-180oF.

PARASCOUR 298 is very effective at higher concentrations in the removal of heavy deposits of grease, dirt, and oil spots. Concentrations of 4-8% may be necessary.

PARASCOUR 298 is biodegradable and will not contribute to water pollution.

SPECIFICATION

Appearance: Clear liquid
Type: Nonionic/Anionic
pH: 10.30
Solubility: Easily disperses in water, forms clear solution
Specific Gravity: 1.00
Odor: Mild

APPLICATION

PARASCOUR 298 PLUS is used in concentrations of 1-3% based on the weight of the fabric.
A typical scour/dye procedure for cotton, wool, or synthetic fabrics is as follows:
- Fill equipment, add PARASCOUR 298 PLUS, and run at 100-140oF, depending on dyestuff being used.
- Add chemicals such as CARRIER MH, SORBASSIST N (wetter), DEFOAMER 019B, JT-4200 (lubricant), or HERRITON RH (leveler).
- Add dyestuff and follow regular dye procedure depending on type of dyes being used.

SPECIFICATIONS

Appearance: Clear liquid
Type: Nonionic/Anionic
pH: 9.5
Solubility: Easily disperses in water, forms clear solution
Specific Gravity: 1.05
Odor: Mild

APPLICATION

PARASCOUR 511 is used in concentrations of 0.25 - 2.0% based on the weight of the fabric.
A typical scour/dye procedure for cotton, wool, or synthetic fabrics is as follows:
- Fill equipment, add PARASCOUR 511 and DEFOAMER 019B; give running wash while loading fabric; run at 140-180° F.
- Add chemicals such as CARRIER MH, SORBASSIST N (wetter), JT-4200 (lubricant), or HERRITON RH (leveler).
- Add dyestuff and follow regular dye procedure depending on type of dyes being used.
The data and suggested formulations in this bulletin are based on information believed to be reliable and are offered solely for evaluation, investigation and

PHYSICAL PROPERTIES

Appearance: Clear liquid
Type: Nonionic
Cloud point: 140° F
pH: 6.0 + 0.5
Solubility: Easily dispersed in water, forms clear solution
Stability: Stable on storage.
Compatibility: Compatible with most surfactants as well as with dilute solutions of acids, salts, and alkalis.

APPLICATION

PARASCOUR KT is used in concentrations of .5 - 2.0% based on the weight of the fabric.
A typical scour/dye procedure for cotton, wool, or synthetic fabrics is as follows:
- Fill equipment, add PARASCOUR KT and DEFOAMER 019B, and run at 100-120° F.
- Add chemicals such as CARRIER MH, SORBASSIST N (wetter), DEFOAMER 019B, JT-4200 (lubricant), or HERRITON RH (leveler).
- Add dyestuff and follow regular dye procedure depending on type of dyes being used.

PHYSICAL PROPERTIES

Appearance: Clear liquid
Type: Nonionic
Cloud point: 130° F
pH: 6.0 + 0.5
Solubility: Easily dispersed in water, forms clear solution
Stability: Stable on storage
Compatibility: Compatible with most surfactants as well as with dilute solutions of acids, salts, and alkalis

APPLICATION

PARASOFT should be applied from a pad or the long bath at 2-6% (O.W.B.) levels. Actual usage concentrations should be determined by individual requirements.

PARASOFT can also be exhausted onto the fabric during the final rinse. Use 2-4% O.W.F. Heat to 110° F and run for 20 minutes. PARASOFT exhaust completely leaving the rinse water clear.

SPECIFICATIONS

Appearance: Off-white liquid
Odor: Pleasant
pH: 3.0 ± 0.5
Solubility: Completely miscible with water at all temperatures
Ionic Type: Cationic
Specific Gravity: 1.01
Package: 450 lb. drum, 2250 lb. totes, Bulk

ADVANTAGES

- Imparts soft, drape-like hand.
- Minimizes crocking.
- Upon drying, will not sublime or drip.
- Highly substantive - small concentrations required.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

APPLICATION

PARASOFT AM should be applied from a pad or the long bath at 2-6% (O.W.B.) levels. Actual usage concentrations should be determined by individual requirements.

PARASOFT AM can also be exhausted onto the fabric during the final rinse. Use 2-4% O.W.F. Heat to 110° F and run for 20 minutes. PARASOFT AM exhaust completely leaving the rinse water clear.

SPECIFICATIONS

Appearance: Off-white liquid
Odor: Pleasant
pH: 3.0 ± 0.5
Solubility: Completely miscible with water at all temperatures
Ionic Type: Cationic
Specific Gravity: 1.01
Package: 450 lb. drum, 2250 lb. totes, Bulk

ADVANTAGES

- Imparts soft, drape-like hand.
- Minimizes crocking.
- Upon drying, will not sublime or drip.
- Highly substantive - small concentrations required.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

APPLICATION

PARASOFT GFI should be applied to the pad at 2-6% (O.W.B.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Viscous emulsion
Color: Off-White
Odor: Pleasant, waxy
Solubility: Miscible in water
Ionic Type: Cationic/nonionic
Density: 8.2 lbs./gallon
Package: 450 lb. drum

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, dry hand.
- Upon drying, will not sublime.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.

APPLICATION

PARASOFT JLB should be applied to the pad at 2-8% (O.W.B.) levels, depending on the desired hand. It may also be exhausted onto the fabric in either jets or becks at 2-8% (O.W.F.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Viscous emulsion
Color: Off-White
Odor: Pleasant, waxy
Solubility: Miscible in water
Ionic Type: Cationic
Density: 8.2 lbs./gallon
Package: 450 lb. drum

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Can also be used to nap fabrics.
- Gives a soft, dry hand.
- Upon drying, will not sublime.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

APPLICATION

PARASOFT LLB should be applied to the pad at 2-4% (O.W.B.) levels. It may also be exhausted onto the fabric in either jets or becks at 1-3% (O.W.F.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Off white liquid
pH: 3.0 ± 0.5
Odor: Pleasant, waxy
Solubility: Miscible in water
Ionic Type: Cationic
Density: 8.2 lbs./gallon
Package: 450 lb. drum, 2250 lb. totes, Bulk

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, dry hand.
- Upon drying, will not sublime.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.

APPLICATION

PARASOFT PG-20 can be either padded on at ½ - 1% (O.W.B.) or exhausted onto fabrics in either jets or becks at ½ - 1% (O.W.F.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Viscous emulsion
Color: Off-white
Odor: Pleasant, waxy
pH: 3.0 ± 0.5
Solubility: Miscible in water
Ionic Type: Cationic
Density: 8.2 lbs./gallon
Package: 450 lb. drum / 2250 lb. tote

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, slick hand.
- Upon drying, will not sublime.
- Will optimize stretch and recovery on manmade fibers.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

APPLICATION

PARASOFT PLB should be applied in the pad at 2-4% (O.W.B.) levels. It may also be exhausted onto the fabric in either jets or becks at 2-4% (O.W.F.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Off white liquid
pH: 4.5 ± 0.5
Odor: Pleasant, waxy
Solubility: Miscible in water
Ionic Type: Cationic
Density: 8.2 lbs./gallon
Package: 450 lb. drums, 2250 lb. totes, Bulk

ADVANTAGES

Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, dry hand.
- Upon drying, will not sublime.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.

APPLICATION

PARASOFT SAM should be applied from a pad or the long bath at 2-5% (O.W.B.) levels. Actual usage concentrations should be determined by individual requirements.

PARASOFT SAM can also be exhausted onto the fabric during the final rinse. Use 2-3% O.W.F. Heat to 110° F and run for 20 minutes.

SPECIFICATIONS

Appearance: Off-white liquid
Odor: Pleasant
pH: 5 ± 1
Solubility: Completely miscible with water at all temperatures
Ionic Type: Cationic
Package: 450 lb. drum

ADVANTAGES

- Will not yellow or scorch.
- Imparts soft, drape-like hand.
- Minimizes crocking.
- Upon drying, will not sublime or drip.
- Highly substantive - small concentrations required.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.
- Can be either padded or exhausted onto the fabric.

APPLICATION

PARASOFT SLB-10 should be applied to the pad at 2-4% (O.W.B.) levels. It may also be exhausted onto the fabric in either jets or becks at 2-4% (O.W.F.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Viscous emulsion
Color: Off-White
Odor: Pleasant, waxy
pH: 3 ± .5
Solubility: Miscible in water
Ionic Type: Cationic/Nonionic
Density: 8.2 lbs./gallon
Package: 450 lb. drum

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, dry hand.
- Upon drying, will not sublime.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

APPLICATION

PARASOFT SLB-2 should be applied to the pad at 2-8% (O.W.B.) levels. It may also be exhausted onto the fabric in either jets or becks at 2-8% (O.W.F.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Viscous emulsion
Color: Off-White
Odor: Pleasant, waxy
pH: 3.0 ± .5
Solubility: Miscible in water
Ionic Type: Cationic
Density: 8.3 lbs./gallon
Package: 450 lb. drum (2250# tote)

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, dry hand.
- Upon drying, will not sublime.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

APPLICATION

PARASOFT WLB should be applied to the pad at 2-8% (O.W.B.) levels, depending on the desired hand. It may also be exhausted onto the fabric in either jets or becks at 2-8% (O.W.F.) levels. Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Viscous emulsion
Color: Off-White
Odor: Pleasant, waxy
Solubility: Miscible in water
Ionic Type: Cationic
Density: 8.2 lbs./gallon
Package: 450 lb. drum

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, dry hand.
- Upon drying, will not sublime.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

APPLICATIONS

PARASTAT A may be applied by padder application. The percentage required will vary with mill conditions but generally 1 to 2 percent of the bath. Percentages of ½% to 1% based on the weight of the solution are recommended as a start for pad application.

PARASTAT A has a broad range of compatibilities and has found use in a wide variety of textile finishing formulas.

SPECIFICATIONS

Appearance: Clear to pale amber liquid
Ionic Character: Anionic
pH (2% solution): 3 – 4
Solubility: Readily soluble in water
Stability: Excellent storage stability
Compatibility: Compatible with dilute solutions of acids, alkalis, and salts; compatible with nonionic and anionic resins.

APPLICATIONS

PARASTAT C may be applied either by exhaustion in the last rinse or by padder application. The percentage required will vary with mill conditions but generally ¼% based on the weight of the fabric will be ample for static elimination. Percentages of ¼% to ½% based on the weight of the solution are recommended as a start for pad application.

PARASTAT C has a broad range of compatibilities and has found use in a wide variety of textile finishing formulas.

PAPER: Use PARASTAT C in sheet forming to promote static free processing. PARASTAT C can also be applied to finished paper with sprays to enhance antistatic characteristics.

SPECIFICATIONS

Appearance: Amber-colored liquid
Ionic Character: Weakly cationic
pH (2% solution): 5-6
Solubility: Readily soluble in water
Stability: Excellent storage stability
Compatibility: Compatible with dilute solutions of acids, alkalis, and salts; compatible with nonionic and cationic softeners and dye fixatives. Also compatible with cationic and nonionic dewatering polymers.

APPLICATION

PARATERG CAT can be used at levels of .5 – 1.5 ounces per 10 pounds of laundry, depending on how heavy the fabric is soiled. For extremely soiled products, apply a small amount of PARATERG CONC to the spot before laundering.

SPECIFICATIONS

Appearance: Clear, yellow liquid
pH (2% solution): 8.0 ± 1.5

APPLICATION

PARATERG CONC can be used at levels of .5 – 1 ounce per 10 pounds of laundry, depending on how heavy the fabric is soiled. For extremely soiled products, apply a small amount of PARATERG CONC to the spot before laundering.

SPECIFICATIONS

Appearance: Clear, slight yellow tint, low viscous liquid
pH: 7.0 – 7.7
Solubility in Water: Complete
Specific Gravity: 1.04

APPLICATION

PARATEX can be used at levels of 1.0 – 2.0 ounces per 10 pounds of laundry.

SPECIFICATIONS

Appearance: Clear viscous liquid with yellow tint

DIRECTIONS

PARATEX BG-355 is used in concentrations from 2% to 50% depending on the degree of stiffness required and the desired use. When padding onto cloth as an anticurl, hand builder, or stabilizer start with a 10% solution and adjust for desired hand. Agitation may be required in the feed tank.

If kiss rolling onto the back of fabric, start with a 50% solution. If an extremely stiff backcoating is needed, use at full strength.

PARATEX BG-355 acts as an excellent adhesive to bond two fabrics together. Spray a light film on one of the substrates and dry thoroughly through a frame.

Clean up with water. If dried, use Rez AwayTM to remove residue.

PHYSICAL PROPERTIES

Appearance: White semi-viscous liquid
Solids: 54 – 56%
Water Solubility: Completely dispersible
Specific Gravity: 1.11
pH: 4.0 – 6.0
Ionic Characteristics: Nonionic

STONE WASH APPLICATION

Liquor Ratio 15:1
pH of Washing Water 4.5-5.5
Parazyme 605 0.5%-1.5% O.W.F.
Temperature 55oC (135oF)
Treatment Time 20-50 minutes

(NOTE: The addition of perlite beads to wash cycle increases the weathered, stone washed look.)

DEPILLING APPLICATION

Liquor Ratio 15:1
*pH of Washing Water 4.5-5.5
Parazyme 605 0.5%-1.5%
Temperature 55oC (135oF)
Treatment Time 10-30 minutes

* Buffering the pH of the washing water must take place prior to the addition of PARAZYME 605.
This can be achieved by using either Citric Acid or Acetic Acid at concentrations of 0.5-1.5% O.W.F. in a 15:1liquor ratio. PARAZYME 605 must be inactivated after the depilling and stone wash applications by either raising the temperature to 70oC (160oF) for 10 minutes or by alkaline rinse with a pH of 9-10.

**Do not store below 32oF or above 80oF. If product is frozen, thaw at room temperature.

SPECIFICATIONS

Appearance: White liquid
Type: Nonionic
pH: 4.0 - 5.0
Solubility: Easily dispersed in water, forms white solution
Specific Gravity: 1.05
Odor: Mild
Water resistance: Good

RECOMMENDED USAGE

Use at 1-100% depending on the application. As an anticurl, 1-5% is recommended. As a back coating, 10-25% is recommended. As an edge gum, 30-50% is recommended.

SPECIFICATIONS

Appearance: White liquid
Type: Nonionic
pH: 4.0 - 5.0
Solubility: Easily dispersed in water, forms white solution
Specific Gravity: 1.05
Odor: Mild
Water resistance: Good

RECOMMENDED USAGE

Use at 1-100% depending on the application. As an anticurl, 1-5% is recommended. As a back coating, 10-25% is recommended. As an edge gum, 30-50% is recommended.

SPECIFICATIONS

Appearance: White liquid
Type: Nonionic
pH: 4.0 - 5.0
Solubility: Easily dispersed in water, forms white solution
Specific Gravity: 1.05
Odor: Mild
Water resistance: Good

RECOMMENDED USAGE

Use at 1-100% depending on the application. As an anticurl, 1-5% is recommended. As a back coating, 10-25% is recommended. As an edge gum, 30-50% is recommended.

SPECIFICATIONS

Color: Clear viscous liquid
Specific gravity: 1.04
pH (2% solution): 5.3 ± 0.5
Solubility: Readily dispersed in water
Stability: Stable on storage - Do not freeze
Compatibility: Compatible with usual finishing agents
Ionic charge: Nonionic
TG: 30
Viscosity @ 25C: 22 ± 2 seconds in #3 cup
Water resistance: Poor

APPLICATIONS

RESYN KLM should be applied on a regular pad as an anticurl on knits. Solution concentrations of 2-5% are generally adequate, but higher or lower amounts may be required to affect the desired hand and properties.

RESYN KLM may also be applied on a kiss roller or in a spray system as a back coating on woven fabrics. A 20% to 30% solution is usually needed to provide proper pickup. Higher or lower amounts may be required depending on desired effects.

SPECIFICATIONS

Color: Clear viscous liquid
Pounds per gallon: 8.67
Specific gravity: 1.04
pH (2% solution): 5.3 ± 0.5
Solubility: Readily dispersed in water
Stability: Stable on storage - Do not freeze
Compatibility: Compatible with usual finishing agents
Ionic charge: Nonionic
TG: 30
Viscosity @ 25C: 700 – 1000 cps
Water resistance: Poor

APPLICATIONS

RESYN KLP-10 should be applied on a regular pad as an anticurl on knits. Solution concentrations of 2-5% are generally adequate, but higher or lower amounts may be required to affect the desired hand and properties.

RESYN KLP-10 may also be applied on a kiss roller or in a spray system as a back coating on woven fabrics. A 20% to 30% solution is usually needed to provide proper pickup. Higher or lower amounts may be required depending on desired effects.

APPLICATION

Resins
Spray full strength onto surface and let set for 1-2 minutes. In most cases, you can spray the resin away with a hose. If resin is difficult, some light brushing may be necessary.

Many applications may permit you to mix REZ-AWAY
Applications include:
- Resin clean-ups from tanks, pumps, and floors
- Cleaning screen printing equipment and screens
- Dye equipment
- Textile dryers
- Metal parts cleaning
- Engine degreasing

PHYSICAL PROPERTIES

Color: Clear to pale yellow liquid
pH: > 12.0
Specific gravity: 1.04
Solubility: Completely soluble in water
Stability: Stable under normal storage conditions. Store above 400F.

APPLICATION

SOFTNAP should be padded on. If applying to dry fabric, 1-2% by weight of bath is sufficient. If applying to wet fabric, higher concentrations will be required. Since the amount of application may vary due to fabric or equipment, actual use rates should be determined to give the most cost-effective results.

SPECIFICATIONS

Appearance: Off-white to translucent liquid
Odor: Mild, Pleasant
Pounds per gallon: 8.28
Type: Nonionic
pH (2% solution): 10 ± 2
Stability: Stable on storage
Stability on freezing: Prevent freezing. Emulsion will separate
Compatibility: With nonionic finishes
Solids: 25 + .5

APPLICATION

SOFTNAP C may be applied by pad or in the bath. If applying to dry fabric, 2-3% by weight of bath is sufficient. If applying to wet fabric, higher concentrations will be required. Since the amount of application may vary due to fabric or equipment, actual use rates should be determined to give the most cost-effective results.

SPECIFICATIONS

Appearance: Cream-colored
Physical Form: Pumpable liquid
Odor: Mild
Type: Cationic
pH (2% solution): 4.0 ± 0.5
Solubility: Disperses readily at 70-90° F
Stability: Stable on storage
Stability on freezing: Prevent freezing. Emulsion will separate
Compatibility: With cationic and nonionic finishes as well as acids, salts, and alkalis
Solids: 15.0 ± 0.5

PHYSICAL PROPERTIES

Color: Light, straw-colored
Physical Form: Liquid
Odor: Mild
Pounds per gallon: 8.4
Type: Anionic
pH (2% Solution): 5.5 ± 0.5
Solubility: Readily soluble in water.
Stability: Stable in normal or heated storage. Will not freeze at 32°F.
Compatibility: Compatible with nonionic and anionic surfactants and stable in dilute solutions of acids, salts, and alkalis.
Cloud Point: Negative

PHYSICAL PROPERTIES

Color: Light, straw-colored
Physical Form: Liquid
Odor: Mild
Pounds per gallon: 8.4
Type: Nonionic
pH (2% Solution): 7.0 ± 0.5
Solubility: Readily soluble in water.
Stability: Stable in normal or heated storage. Will not freeze at 32°F.
Compatibility: Compatible with nonionic and anionic surfactants and stable in dilute solutions of acids, salts, and alkalis.
Cloud Point: Negative

APPLICATION

SPL-325 should be either padded on at ½ - 2% (O.W.B.). Actual usage concentrations should be determined by individual requirements.

SPECIFICATIONS

Appearance: Viscous emulsion
Color: Off-white
Odor: Pleasant, waxy
pH: 3 ± .5
Solubility: Miscible in water
Ionic Type: Cationic
Density: 8.2 lbs./gallon
Package: 450 lb. drum / 2250 lb. tote

ADVANTAGES

- Highly concentrated product so lower percentages can be used.
- Will not yellow or scorch.
- Gives a soft, slick hand.
- Upon drying, will not sublime.
- Will optimize stretch and recovery on manmade fibers.
- Can be either padded or exhausted onto the fabric.
- Generally compatible with all typical resin formulations.
- Will not pollute; biodegradable.

SPECIFICATIONS

Appearance: Off-white semi-transparent liquid
Type: Nonionic
pH (2% solution): 5.5 +/- 1
Solubility: Completely soluble in water
Specific Gravity: 0.99
Odor: Very slight mild odor

APPLICATION

WIK-AWAY must be padded onto the substrate at a rate of 1-3%. To test use a 2% solution and adjust as required. Dry thoroughly at 260° - 280°F.

SPECIFICATIONS

Appearance: Off-white semi-transparent liquid
Type: Nonionic
pH (2% solution): 5.5 +/- 1
Solubility: Completely soluble in water
Specific Gravity: 0.99
Odor: Very slight alcohol odor

APPLICATION

WIK-AWAY II can be either added into a rinse cycle and heated to boil or padded onto the substrate at a rate of 2 – 3%. To test use a 2% solution and adjust as required. Dry thoroughly at 260° - 280°F. Our internal testing shows that there may be improved results when the product is applied in a rinse and heated to boil for 10 minutes. However, it may be less expensive to pad the WIK-AWAY II onto the substrate.